DEFINITION :
Very thick solvent-free epoxy covering for concrete or hydraulic mortar floors.

DESTINATION :
For floors subjected to heavy mechanical and chemical constraints.

PROPERTIES :
Very high gloss finish, good smooth finish, very resistant to chemicals and wear.

TECHNICAL SPECIFICATIONS :
Presentation: Three packs to be mixed before use
• Component A: Colored resin
• Component B: Hardener
• Component C: Aggregat resin and hardener: semi-fluid epoxy resin
• Hardener: cycloaliphatic polyamine
• Aspect: Gloss
• Color: White and Floor color range, RAL color chart
• Dry extract: 99 to 100% by weight, 98 to 100% by volume (depending on color)
• Density: 1.72 to 1.85 (depending on color)

APPLICATION SPECIFICATIONS :

• Application: 1 coat
• Tools: Toothed spatula and roller
• Conditions:   Temperature above 10°C (surface and air temp). Temp. must be at least 3°C above dew-point.
Do not apply above 25°C (reduced application time). Humidity below 65% .

• Yield: 1800g/m² per mm of thickness.
• Dry: 10 hours
• Light use: 24 hours
• Heavy use: 48 hours
• Complete hardening: 5 days
•  Practical Usage Time: 30 minutes at 20°C
•  Thinner: Do not thin
•  Recommended primer:  PRIMAIRE 411-200, 411-80, or 411-80S, depending on surface
• Cleaning: DAF 315
 
RECOMMENDATIONS FOR USE:

Comply with DTU N°59-3 “Floor Paint”, which defines surface quality required and measures to be taken prior to implementation (note that surface must be sound, clean, dry, and absorbent), as well as DTU N°54.1 “Synthetic-resin-based liquid floor coatings”.

SURFACE PREPARATION :

• Soundness: Surface cohesion > 1MPa = 100N/cm² for concrete, > 0.5MPa/cm² for mortar.
• Cleanliness: Soiling and grease to be removed with DEGRAISSANT LT615, followed by thorough rinsing.
• Dryness: < 4% humidity for concrete and mortar. Absence of rising damp.
• Absorption:
Water droplet test: absorption must be complete from 60 to 240 seconds. Specific surface treatment required if this is not the case.
If applied to an existing coating in good condition, verify compatibility and adherence by prior test.

MIXTURE PREPARATION:

Using a slow-speed mixer, mix the pre-dosed packets by pouring component B into resin A. Slowly add component C while mixing until a homogenous mixture is obtained.
Once mixed the practical usage time is 30 minutes at 20°C. The product then gradually thickens and heats up as it hardens. This process is irreversible.

NEVER ADD THINNER DURING APPLICATION. DURING STORAGE PROTECT THE PRODUCT FROM HEAT AND DIRECT SUN.

IMPLEMENTATION:

Pour the homogenously mixed product onto the floor and spread uniformly with a pointedtooth spatula. Tooth height should be twice that of the required coating thickness. Roll to eliminate air-bubbles and obtain a perfect surface. In order to maintain the regularity of surface thickness, change the toothed spatula every 50 to 75m².

SUPPLEMENTARY INFORMATION :

• Transport classification:
• Component A: Class 9, Packaging group III, transport category 3
• Components B and C: Class 8, Packaging group III, transport category 3

Official transport designation:

• Component A: UN 3082, dangerous for the environment, N.S.A., epoxy paints, 9, III, (E)
• Components B and C: UN 2735, corrosive polyamine liquids, N.S.A., products assimilated to paint, 8, III, (E)
• Packaging: 20kg
• Storage: 6 months in unopened canisters
• Health and safety: Xi – irritant. Contains epoxy compounds. • European classification: Category A, Sub-category j (directive 2004/42/CE) max EU VOCs: For sub-category j: 500g/l (2010) Max VOCs this product: 90g/l